Skip to content
Cart

Collection: Green Network Cables

Shop green Cat5e, Cat6 and Cat6A patch leads in stock now at TechLoop, with fast Australia-wide delivery.

Compare (0/5)

64 products

Astrotek

Astrotek CAT6 Ethernet Cable Green 10m

Regular price
Sale price $8.94 Regular price $17.00

Astrotek

Astrotek CAT6 Ethernet Cable Green 5m

Regular price
Sale price $6.94 Regular price $10.00

StarTech.com

StarTech CAT6 7.5m Green Snagless PoE Ethernet Cable 250MHz 24AWG

Regular price $23.00
Sale price Regular price

StarTech.com

StarTech CAT5e 2m Green Snagless RJ45 Patch Cable 24AWG Gold Plated

Regular price $11.00
Sale price Regular price

Which green network cables do you actually need?

Most PC builders treat Ethernet cables as an afterthought, then wonder why a 2.5GbE port is linking at 1Gbps. The green jacket is just colour coding, handy for marking a LAN run, an IoT or guest VLAN, or a link to a specific switch. What matters is what's inside it. Entry-tier green cables are usually Cat5e or basic Cat6 in UTP (unshielded) construction. They're fine for 1Gbps and 2.5Gbps over typical home distances, and Cat5e is rated to 100MHz, which is enough for 2.5GBASE-T over a full 100 metres. The sweet spot is a pure copper Cat6 or Cat6A patch cable with snagless boots. Cat6 is rated to 250MHz and handles 10Gbps up to about 55 metres. Cat6A is rated to 500MHz and handles 10Gbps over the full 100 metres, with better alien crosstalk rejection, which matters in bundled runs. Enthusiast cables are Cat8 or Cat6A S/FTP, with foil around each pair plus an overall braid. That helps in electrically noisy environments such as server racks or runs alongside power cabling. Diminishing returns hit hard here, because Cat8 is rated to 2000MHz but only for short 25 to 30 metre runs at 25 or 40Gbps. Almost no home board or router uses those speeds, so you're paying for headroom you can't plug into. Cable latency also doesn't change between tiers. Signal travels at roughly the same speed, so a pricier cable won't drop your ping.

Upgrading and technical nuances

Check the ports on your gear before choosing a cable. Many current Motherboards on AM5 and LGA1851 ship with 2.5GbE, and higher-end boards add 5GbE or 10GbE. A 10GbE link over Cat5e might negotiate down or become unstable, but a clean Cat6A run avoids that. If your router and switch from Networking are only 1GbE, a Cat6A cable won't speed anything up. The bottleneck is the slowest link in the chain. Gear such as TP-Link Archer routers, Deco mesh systems and Omada switches increasingly offers 2.5G ports, so a Cat6 baseline makes sense for new runs.

Shielding is a real engineering trade-off. UTP is thinner, more flexible and cheaper, and works well in a typical home or office. Shielded FTP or S/FTP cable rejects interference better, but it's stiffer, with a larger bend radius, and shielding only helps if the plugs and ports are properly grounded. A shielded cable in an ungrounded setup can perform worse than a decent UTP one. For most builders, UTP Cat6 or Cat6A is the right call.

Conductor material is where cheap cables cut corners. Copper-clad aluminium (CCA) has higher resistance and is more brittle. It struggles at longer lengths and with Power over Ethernet, where extra heat builds up in the cable. Look for "100% pure copper" or "bare copper" in the spec. Conductor gauge matters too. 24AWG is typical for solid in-wall cable, while patch cables are often 26AWG or 28AWG stranded. Slim 28AWG patch cables are great for tidy builds and short runs, but avoid them on long PoE runs.

Brands worth searching for include Ubiquiti UniFi patch cables, Cable Matters Cat6 and Cat6A snagless ranges, Ugreen Cat6 and Cat8 cables, and Belkin Cat6 patch leads. For in-wall runs, Cat6A bulk cable from Panduit, Dintek or Clipsal is the standard electricians use.

Practical things to check before you buy

Measure the run first. Patch cables are typically sold from 0.5m to 30m, and a bit of slack beats a stretched plug. A cable that's too long creates clutter, while one pulled tight stresses the RJ45 connector. Inside a PC, you'll rarely run Ethernet through the case itself, but leave room for the rear I/O. Many Computer Cases have tight rear gaps against a wall or desk, so a right-angle or slim-boot cable can help.

Check the jacket type. PVC is standard for home use. LSZH (low smoke zero halogen) is better for enclosed or commercial spaces, where fire safety rules matter. For cable routing near Power Supplies, keep Ethernet separated from mains cabling where you can, and cross at right angles rather than running parallel for long distances. That cuts interference, particularly with unshielded cable.

Look for TIA/EIA-568 compliance and a printed Cat rating on the jacket. If you're running a NAS or a game streaming setup, a stable wired link beats Wi-Fi for latency and packet loss. Pair it with good gear from Cables & Connectors, and make sure the plug latch is intact, since a snapped clip is the most common failure. Flat cables are easy to slip under doors, but most are only rated Cat6 at best and can have worse crosstalk, so use them for short hops rather than backbone runs.

If you're building a full system, whether from scratch or from Computers, a quality cable between your PC and the switch is the cheapest part of the network and the easiest to get right.

Brands and local warranty

Reputable names include TP-Link, Ubiquiti, Belkin, Cable Matters, Ugreen and Linksys, with Panduit and Clipsal on the structured cabling side. Warranty on a patch cable is rarely a headline feature, but local support matters more once you're buying switches, access points and routers alongside them. A genuine Australian warranty means you deal with a local return process rather than shipping something overseas. It also means gear built to Australian compliance standards, with RCM marking on powered devices. Dodgy imported cables often lack proper certification, and they're the ones that come up with CCA conductors or misprinted category ratings. Keep your invoice, and if a cable fails to hold its negotiated speed, test with a known good one before blaming the port.

Frequently asked questions

Does a green Ethernet cable perform differently from other colours?

No. Jacket colour has no effect on speed or signal quality. Green is just a labelling choice. The category rating, conductor material and construction decide how it performs.

Is Cat6 enough for 2.5GbE and 10GbE?

Cat6 handles 2.5GbE with no trouble and 10GbE up to about 55 metres. For longer 10GbE runs, or cables bundled tightly with others, go Cat6A.

Do I need Cat8 for gaming?

No. Game traffic needs very little bandwidth, and what matters is a stable, low-loss connection. A good Cat6 or Cat6A cable delivers the same latency as Cat8 for any home setup.

Why is my cable only linking at 100Mbps or 1Gbps?

Usually it's a damaged plug, a broken pair inside the cable, or a port on the router or switch that doesn't support higher speeds. Swap in a known good Cat6 cable and check the link speed in your OS network settings.

Is CCA cable safe to use?

It works at short distances for basic data, but it's more fragile and a poor choice for PoE devices like cameras or access points. Buy pure copper for anything permanent.